Site Navigation

Your Account

Choose Language

Introduction

These are the instructions for putting together your Pro Camera-HD Upgrade. You can purchase this product from our store.

You will find the acrylic pieces you need in both the 6mm and 3mm bags of acrylic.
  • You will find the acrylic pieces you need in both the 6mm and 3mm bags of acrylic.

  • You may have some acrylic pieces that have some debris from the laser cutting process in the holes. They should come out easily pushing them through.

Add Comment

Before starting each section make sure to remove the paper backing from the pieces used only in that section.
  • Before starting each section make sure to remove the paper backing from the pieces used only in that section.

  • A knife or your fingernails can be used to start removing the paper from a corner.

  • Use caution when using sharp tools.

Add Comment

The cement is solvent based, meaning it is not sticky but as it cures it bonds like materials.
  • The cement is solvent based, meaning it is not sticky but as it cures it bonds like materials.

  • Before you start, watch this great video on how to use acrylic cement from TAP Plastics.

    • The best way to apply cement is to hold the syringe bottle upright (tip at the top) and squeeze out a bunch of air, so when you turn the syringe bottle upside-down (and don't squeeze the bottle), air will burble inward and not allow cement to flow out. When you're ready to apply cement, lightly squeeze the bottle to overcome the vacuum pressure.

    • Only a little cement is required to make a good bond. Use the capillary effect to apply cement to a joint and have the cement work its own way into the space.

    • The acrylic cement does drip and should be done over a surface that can get dirty. Paper towels work well for this.

  • When working with acrylic cement it is recommended that you wear gloves, safety glasses, and work in a ventilated area.

Add Comment

|
  • |

Add Comment

The 1.5mm piece of black acrylic is in a different bag.
  • The 1.5mm piece of black acrylic is in a different bag.

Add Comment

The piece with the smaller holes is on the bottom.
  • The piece with the smaller holes is on the bottom.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Make sure you have the piece with the square holes.
  • Make sure you have the piece with the square holes.

Add Comment

Make sure it is flush in both directions.
  • Make sure it is flush in both directions.

Add Comment

|
  • |

Add Comment

Make sure it is flush in both directions and at a right angle.
  • Make sure it is flush in both directions and at a right angle.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Make sure you have the piece with the cutouts.
  • Make sure you have the piece with the cutouts.

Add Comment

The edge piece is pointing up.
  • The edge piece is pointing up.

  • The tab is on the outside.

  • The large opening is to the left.

Add Comment

The edge piece is pointing up.
  • The edge piece is pointing up.

  • The tab is also on the outside.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

This piece is on the same side as the semi-circle opening.
  • This piece is on the same side as the semi-circle opening.

Add Comment

|
  • |

Add Comment

Video (How to Solder Electronics)
  • Video (How to Solder Electronics)

  • Use caution when soldering electronic components. The temperatures are 500 degrees F and higher. Eye protection is required.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Make sure the wires are on the same side as the text labels.
  • Make sure the wires are on the same side as the text labels.

    • The red wire is the +

    • The black wire is the -

Add Comment

Repeat for the LASERS on the other side.
  • Repeat for the LASERS on the other side.

Add Comment

There are three lasers in the kit. You will only use two of them.
  • There are three lasers in the kit. You will only use two of them.

  • The blue/black wire is the negative wire and the red wire is the positive wire.

Add Comment

Repeat for the other laser.
  • Repeat for the other laser.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Make sure the logo is upright.
  • Make sure the logo is upright.

  • Make sure the holes are at the top.

Add Comment

|
  • |

Add Comment

Note the orientation of the camera standoffs.
  • Note the orientation of the camera standoffs.

Add Comment

|
  • |

Add Comment

Insert the M2x12 screw.
  • Insert the M2x12 screw.

Add Comment

|
  • |

Add Comment

You will only use three screws.
  • You will only use three screws.

Add Comment

These o-rings will hold the corrective lens.
  • These o-rings will hold the corrective lens.

Add Comment

|
  • |

Add Comment

Place the other o-ring on the other side.
  • Place the other o-ring on the other side.

  • These should be in the grooves on the lens mount.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

The red and black wires go through the middle hole.
  • The red and black wires go through the middle hole.

  • Make sure the camera is on the same side as the semi-circle.

  • Make sure the Camera Mount Assembly is not upside down.

  • Make sure the opening is at the top.

Add Comment

Do not tighten the nut all the way.
  • Do not tighten the nut all the way.

Add Comment

Tighten this side so the camera platform stays on, but can still move up and down.
  • Tighten this side so the camera platform stays on, but can still move up and down.

Add Comment

Tighten the other side, but have it still loose enough the platform can still move up and down.
  • Tighten the other side, but have it still loose enough the platform can still move up and down.

Add Comment

Make sure to screw on the nut snugly to allow the camera mount to rotate up and down without much resistance.
  • Make sure to screw on the nut snugly to allow the camera mount to rotate up and down without much resistance.

Add Comment

Make sure to screw on the nut snugly to allow the camera mount to rotate up and down without much resistance.
  • Make sure to screw on the nut snugly to allow the camera mount to rotate up and down without much resistance.

This step seems to be a duplicate of step 51

Przemyslaw Karwasiecki - Reply

Step 51 is when the camera is at the top of the range of motion...Step 52 is when the camera is at the bottom. We want to make sure that you have the full range of motion. -Brian G.

OpenROV -

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Make sure you have slack in the camera wire.
  • Make sure you have slack in the camera wire.

Add Comment

This is not enough camera wire slack.
  • This is not enough camera wire slack.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

The servo should be flush.
  • The servo should be flush.

It is hard to make it flush, as servo thickness is 11.8mm, and the glued bracket provides only 10.5mm depth.

I hope this is still OK, even if servo sticks out 1.3mm over the acrylic plate.

Przemyslaw Karwasiecki - Reply

Yes this is ok - Brian G.

OpenROV -

The wires should be going towards the same side as the vertical plate.
  • The wires should be going towards the same side as the vertical plate.

Add Comment

The wires should be coming through this slot.
  • The wires should be coming through this slot.

Add Comment

Do not tighten so much that the board bends more than in this image.
  • Do not tighten so much that the board bends more than in this image.

Add Comment

Make sure you have installed all 4 screws.
  • Make sure you have installed all 4 screws.

Add Comment

Make sure your electronics board is not bending.
  • Make sure your electronics board is not bending.

Add Comment

|
  • |

Add Comment

Make sure black wire is oriented to the outside of the board.
  • Make sure black wire is oriented to the outside of the board.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Check the labels on the light board and follow the red and black wires.
  • Check the labels on the light board and follow the red and black wires.

Add Comment

P1- is the black wire connected to the lights (see label on back of light board).
  • P1- is the black wire connected to the lights (see label on back of light board).

  • P1+ is the red wire connected to the lights.

  • P2- is the black wire connected to the lasers.

  • P2+ is the red wire connected to the lasers.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Insert the microSD card into the BeagleBone Black.
  • Insert the microSD card into the BeagleBone Black.

hi, I got confused about the guides between "Update Software Image From SD Card" and "Pro Camera-HD Upgrade".

I am having the OpenROV v2.8 Kit Pro Bundle.

I suppose the SD card comes with the Pro Camera-HD has built-in software image 30.1.0.

Do I need to complete the "Update Software Image From SD Card" guide before this step?

Jianxiao - Reply

figured it out. For v2.8 with Pro Camera HD, there is no need to perform "Update Software Image From SD Card" which will flash the SD card with 30.0.3 software.

Just burn in the latest image from this link and all works fine.

https://forum.openrov.com/t/new-release-...

cheers!

Jianxiao - Reply

|
  • |

Add Comment

|
  • |

Add Comment

This is the corrective lens for the camera. This lens corrects for the astigmatism caused by the tube.
  • This is the corrective lens for the camera. This lens corrects for the astigmatism caused by the tube.

  • To keep it clean, only handle it from the sides.

Add Comment

The lens looks like this picture.
  • The lens looks like this picture.

    • Curved side

    • Flat side

  • The flat side will be on the camera side, and the curved side will be facing out.

Add Comment

|
  • |

Add Comment

|
  • |

Add Comment

Plug the electronics chassis into your ROV.
  • Plug the electronics chassis into your ROV.

Add Comment

Add Comment

Finish Line

One other person completed this guide.

OpenROV

Member since: 09/28/2013

26,001 Reputation

36 Guides authored

Team

OpenROV Internal Member of OpenROV Internal

Community

1 Member

36 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 5

Past 30 Days: 28

All Time: 667